Carburetor tune-up cleaners or any type of solvent cleaners will damage the internal components of the valve. Our discount used 2000 Ford F-150 transmissions come directly from a dependable network of modern junk yards. Lower it to the ground with the torque converter installed. Go to your Honda dealership and get Honda Manual Transmission fluid or just buy some 10W40 and put that in there it will work either way. Well actually your suppose to change the filter in the transmission every 10000 miles.
You should have your fluid level with the fill plug hole. Due to the diode in the solenoid, you may have to reverse the leads to get a reading. Remove all electrical and mechanical connections, including the shifter linkage, transmission lines, the electronic harness and any vacuum lines. If you have any questions, please call us at the Ford Special Vehicle Team hotline from 8:30 a. Buying a used 2000 Ford F-150 transmission from a non-reliable dealer is an unnecessary risk.
If a spark plug is removed for inspection, it must be reinstalled in the same cylinder. Refer to your Scheduled Maintenance Guide to determine the correct service interval. Lower it to the ground with the torque converter installed. This transmission unit includes a transmission case, valve body, tail shaft and housing, torque converter automatic only , and all internal lubricated parts. This transmission unit includes a transmission case, valve body, tail shaft and housing, torque converter automatic only , and all internal lubricated parts. Drain the transmission fluid from the transmission by removing the transmission pan. This transmission unit has been inspected, tested and ready to ship.
. Do not overfill it so it runs out of the hole this will be too much. We sell only high quality used Ford F-150 automatic transmissions, with 1-3 years warranty and free shipping. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. I also have an occasional grinding from 2nd to 3rd gear that I have taken it in for several times only to be told sorry we cant recreate the problem. One could also choose either 2 or 4 wheel drive. It should separate from the engine easily.
How to Remove the 4R70W Transmission from Your F150 Posted by on Tuesday, September 23rd, 2014 The 4R70W is a four-speed automatic transmission produced by the Ford Motor Company. Re-attach the pan with a couple of bolts to hold it in place. The valve is located on the side of the throttle body. A complete fluid exchange service, performed annually, can add years to your transmissionï¿½s life. It stays there for about 60 seconds and goes back to 800. This allows the transmission to slip and overheat, and quickly cause it to fail. Browse our online catalog and.
I waited about 15 minutes and it started. Look on the side of the transmission. Choose Your Option Automatic Transmission 6 Cyl, 255 cid 4. Remove the bolts that hold the torque converter to the flex plate. To check the gearbox oil first you have raise the vehicle to a height that you can get underneath it then locate the gearbox it should be bolted to the back of the engine when you have found it look at both sides of the gearbox till you see a large bolt, you will have to undo this bolt It is calle … d the filler plug once you have this bolt out the oil should be level with the bottom of this hole if so your gear box is full to its correct level if not then you will have to top it up with the correct type of oil hopr this helps.
It was also found in the pickup truck. Be sure to place a drain pan under the tail of the transmission to catch any fluid that may run out. There are 15 choices for the 2000 Ford F-150 Transmission Assembly!!! Go to your Honda dealership and get Honda Manual Transmission fluid or just buy some 10W40 and put that in there it will work eith … er way. Once on the ground, slide the transmission out and away from the bottom of your truck. Make sure you jack it up on completely level ground. The Fill plug is also on the drivers side about half way up and is the same size as the Drain Plug. Carefully remove the bolts that hold the transmission case to the engine block.
Power steering fluid reservoir 3. Remove the inspection plate from the front of the transmission case. Using a transmission jack, slightly put pressure on the transmission case. Remove the inspection plate from the front of the transmission case. Remove all electrical and mechanical connections, including the shifter linkage, transmission lines, the electronic harness and any vacuum lines.